← Back to Part 2 Modules
PART 2 · ADVANCED BGP THEORY · MODULE L

Module L – BGP Route Reflectors

Lesson content presented from the approved Part 2 master documentation.

Route Reflectors reduce the need for a full iBGP mesh by reflecting selected routes between clients while using attributes to prevent reflection loops.

Learning objectives

1. Full mesh scaling

Without route reflection, iBGP requires a full mesh so routes learned from one iBGP peer are not re-advertised to another iBGP peer. Session count is N(N−1)/2.

RoutersFull-mesh sessions
46
1045
20190
501,225

2. Reflection rules

Route sourceRR may advertise to
eBGP peerEligible iBGP clients and non-clients
RR clientOther clients and non-clients
RR non-clientClients only

Non-client iBGP peers still require a full mesh among themselves unless another supported architecture is used. An RR normally reflects its selected best path, which can cause path hiding.

3. Cisco IOS configuration

router bgp 65001
 neighbor 10.0.0.2 remote-as 65001
 neighbor 10.0.0.2 route-reflector-client
 neighbor 10.0.0.3 remote-as 65001
 neighbor 10.0.0.3 route-reflector-client

4. Loop prevention

5. Redundancy, path hiding and Add-Path

Multiple RRs improve resilience. Clients may peer with more than one RR. Since an RR generally advertises its selected best path, another useful path can be hidden. BGP Add-Path allows multiple paths to be advertised when supported and configured.

Lab extension

Preserve the existing four-router EVE-NG baseline. Add a separate R5 or clone a snapshot for RR experiments; verify interface mappings and software support.

Senior QA scenarios

IDTestExpected result
L-01Calculate mesh for N routersN(N−1)/2.
L-02Client route learnedReflected to eligible clients/non-clients.
L-03Non-client route learnedReflected to clients only.
L-04Own Originator ID returnsOriginal router rejects route.
L-05Own Cluster ID presentRR rejects looped route.
L-06RR failure with redundant RRAlternate RR maintains/re-establishes reachability.
L-07Two candidate paths at RRBest-path reflection verified.
L-08Enable Add-PathMultiple paths advertised/received as configured.
L-09Client/non-client policyNo unintended propagation.
L-10RR failure and recoveryRoute and forwarding recovery measured.

Interview questions

Student Knowledge Assessment – Module L (reconstructed)

Q1. How many full-mesh iBGP sessions are required for 5 routers?

A. 5

B. 10

C. 15

D. 20

Correct answer: B. 10

Explanation: N(N−1)/2 = 5×4/2 = 10.

Q2. What is the main purpose of an RR?

A. Replace TCP

B. Reduce full-mesh iBGP peering requirements

C. Encrypt updates

D. Assign ASNs

Correct answer: B. Reduce full-mesh iBGP peering requirements

Explanation: An RR reflects eligible routes to clients.

Q3. A route learned from an RR client can be reflected to:

A. Only source client

B. Other clients and non-clients

C. Only eBGP peers

D. No peers

Correct answer: B. Other clients and non-clients

Explanation: Client-learned routes can be reflected to other clients and non-clients.

Q4. A route learned from a non-client is reflected to:

A. Other non-clients only

B. Clients only

C. All peers

D. No one

Correct answer: B. Clients only

Explanation: Non-client-learned routes are reflected to clients only.

Q5. What does Originator ID identify?

A. Original router injecting route into reflection

B. TCP server port

C. Local preference

D. Cluster count

Correct answer: A. Original router injecting route into reflection

Explanation: Originator ID records the originating router ID for loop prevention.

Q6. What does Cluster List contain?

A. ASNs

B. Cluster IDs traversed

C. Interface addresses

D. MED values

Correct answer: B. Cluster IDs traversed

Explanation: Cluster List records the route-reflector cluster path.

Q7. What is path hiding?

A. Route hidden by ACL

B. RR advertises selected best path and may not advertise another useful path

C. TCP encrypted

D. Route not originated

Correct answer: B. RR advertises selected best path and may not advertise another useful path

Explanation: Best-path-only reflection can hide alternate paths.

Q8. What does Add-Path enable?

A. Multiple paths advertised

B. Multiple TCP ports

C. More ASNs

D. Zero Hold Time

Correct answer: A. Multiple paths advertised

Explanation: Add-Path allows multiple paths for a prefix to be advertised.

Q9. Do RR clients need direct sessions to each other in a standard RR design?

A. Yes always

B. No, not for the client mesh served by RR

C. Only eBGP

D. Only with MED

Correct answer: B. No, not for the client mesh served by RR

Explanation: Clients exchange routes through the RR.

Q10. Why use redundant RRs?

A. Remove policies

B. Improve resilience and avoid a single RR failure point

C. Disable AS_PATH

D. Replace IGP

Correct answer: B. Improve resilience and avoid a single RR failure point

Explanation: Redundant RRs improve control-plane resilience.

Source and assessment note

Technical explanations, tables, examples, QA scenarios and assessments are presented from the approved Part 2 master documentation. Verify illustrative CLI syntax against the target router platform and software release before lab or production use.